Fetter Pro Documentation
Installation, quick start, every setting, padlocks and hooks, workflows, FAQ and troubleshooting for the Fetter Pro Blender add-on.
What Fetter Pro is
Wrap chains and ropes around any mesh in one click. Drag a line across your prop, or pick a few of its edges or faces, then dial in the turns, the spacing, the tilt and the link size live. Chained coffins, bound crates, roped barrels, sealed chests, shackled statues, a skeleton tied to a tree. Or hang a chain between two posts, lay a chain or a rope along any curve, or coil a rope on its own: hung on a nail, dropped on the floor or laid flat.
Every link is a real interlocking link that never cuts into the prop or into its neighbours, and every closed ring closes seamlessly. Lock a chain shut with a padlock, or end it with a forged hook.
Draw Chain or Rope -> Tune it live -> Finalize -> Export
Features
- Four ways to pick: several separate edges along the object (for example the 4 long corner edges of a crate) or the faces of the parts to wrap: the wrap goes around them and nothing else, the turns spread where they all stand. Or one edge loop around the object, or an open edge path that the chain or rope follows. In Edit Mode a line tells you live what your selection will give.
- One wrap per part: select the faces of several posts and wrap each one on its own.
- Any number of turns: rings (one closed loop per turn) or one continuous spiral, spread over the selection, centered, forward or backward. Turns never come closer than the chain or rope is wide.
- Crossed patterns: tilt the rings and alternate the tilt to get X crossings, like a chest chained shut, or randomize tilt and offset with a seed.
- Real interlocking links: every link alternates 90 degrees with its neighbour, closed rings always close seamlessly (even link count), and links never intersect each other, even at sharp corners or crossed at 45 degrees.
- Five link shapes: oval, square, round, stud (a bar across each link, as on an anchor chain) and twisted.
- Tight wrap: the wrap follows the object like a chain pulled tight: flat on the faces, bridging corners with a link straddling the edge, never inside the mesh.
- Tighten and Slack: one slider closes the chain or rope in until it rests on the surface, or pushes it away; another lets the rings hang loose and sag under a beam.
- Follow Shape: the wrap hugs the part of the mesh it goes around. A chain on a shaft stays on the shaft, even between a wide base and a wide head, and other parts of the mesh are left out.
- Draw Wrap: no Edit Mode and no edge to select. Drag a line across the object and the wrap goes around it there, on any mesh.
- Hang between two objects: select two posts and a chain or rope hangs between them, with a Sag setting. Move either post and it follows.
- Tie Another Object: wrap a tree, click the skeleton with the pipette, and the rope ties the two together.
- Chain and Rope on Curve: click a curve with the pipette and a chain or a rope lies along it, every spline of it (Bezier, poly or NURBS), with all the link, rope, padlock and hook settings. Edit the curve and it follows.
- Coiled Rope and Coiled Chain: a coil on its own, made at the 3D cursor. Hanging: loops hung on a peg, gathered on it so a nail or a short hook holds them, its origin on the peg to snap it onto your scene. Lying: the same loops dropped on the floor, lying on each other. Flat: a neat spiral. The rope never passes through itself.
- Crossings go over: a ring that crosses another lifts over it. Wraps built later on the same object go over the earlier ones.
- Twisted rope: 1 to 8 strands, adjustable twist, seamless closed loops, and ends cut plain, frayed, whipped or tied in a stopper knot.
- Padlocks and hooks: hand-modelled Medieval (shield) or Modern (block) padlocks threaded through an upright link, a forged eye hook or an S-hook on free ends: game ready, under 1,500 triangles each, unwrapped with no overlap.
- Presets: Prison Chain, Anchor Chain, Fine Chain, Ship Rope, Rope Coil and Game Low Poly in one click.
- Live and non-destructive: every setting rebuilds the wrap at once, and Undo brings back the wrap with its settings. The wrap stays parented to its target and follows it, its edits, its modifiers and its pose. Finalize turns it into a plain mesh.
- Game-ready output: one mesh, smooth shading, your own materials kept, UVs shared (tiling materials) or unique per link (texture painting), a color per link for wear variation, LODs and a _low / _high bake pair in one click.
- Real low poly rope: Plain Tube turns a rope into a simple tube that follows it, a small share of the triangles (61,000 down to 4,200 on a coil). The bake pair of a rope makes its _low as that tube, its _high the twisted rope.
- Low poly to high poly: set the triangle budget of one link, from 36 to 4096. A wrap too heavy for Blender is refused with what to change, instead of freezing it.
- Its own panel: a dark card with cyan accents in the Fetter tab, in the order of the work. Rest the pointer on any control for half a second and a popup explains it with a small diagram.
- Any scale: default sizes follow the scene unit scale (meters or centimeters).
Where to start
- Installation — requirements, install, update.
- Quick start — your first chain around a crate.
- Drawing a wrap — drag a line across the object, no edge to select.
- Hanging between two objects — a chain or rope hanging between two posts.
- Picking the edges — separate edges, faces, an edge loop or a path.
- Tie Another Object — tie a second object in with the pipette.
- Chain or rope on a curve — a chain or rope laid along a curve you pick.
- Coiled rope or chain — a coil on its own, hung on a peg or dropped on the floor.
- The Fetter panel — the card, in the order of the work, help popups and classic panels.
- Settings — every setting, its default and its effect.
- Accessories — padlocks and hooks.
- Game asset workflow — materials, UVs and export.
- FAQ and Troubleshooting.
Last updated: 2026-11-18