Candles on an object
Stand Souls Candle candles on a skull, an altar or a step with Build on an Object..., slide them with G: the wax follows the surface and drips over its edges.
Candles can stand on any mesh object — the support. The wax then follows its surface, pools where it is flat and hangs from its edges as drips ending in drops.
Steps
- Press Build on an Object… (next to New Seed, under BUILD CANDLE), then click the object in the viewport (skull, altar, step…). A new candle stands where you clicked — on top when you click a side — with the current settings. Stands On switches to Object and the object becomes the Support.
- To put it somewhere else on the object, press G (or Slide on Object (G) in the Placement section) and move the mouse: the candle follows it on the surface. Left click drops it, Esc or right click cancels. Middle mouse and the numpad still move the view.
- To move it onto another object, select it and use the eyedropper next to Support (Placement): click the other object, the candle goes there, where you click.
- Moved or edited the support afterwards? Select the candle and press Rebuild Selected to fit it again.
G only does this for the one selected candle standing on an object. On every other object it keeps its usual meaning. To lift a candle off its object, set Stands On to Ground first.
Supports with several levels
A support made of one mesh with several levels — shelves, steps, niches — works too. The candle stands on the level you click with Build on an Object… or the eyedropper, on the level the mouse points at with G, or on the level under the 3D cursor with BUILD CANDLE, and it stays on that level when you press Rebuild Selected.
Where a candle can stand
- The surface under its rim may not rise by more than its radius: a candle does not stand against a steep side.
- At most 3 of 8 points around its rim may hang past an edge.
- When the mouse is over a place it cannot stand, the candle stops at the nearest place it can.
- In a group, only the middle of the group is checked. The other candles follow it, and a candle that finds nothing under it, past the edge of the support, is skipped.
How the candles find their place
- Each candle looks straight down onto the support from just above the candles and stays upright.
- Each candle sits on the surface under its center and goes down into it a little, so there is no gap on a sloped or curved surface.
- The candle object’s origin is put on the support. That is the pivot you get in the FBX.
- While a candle slides, its wax is rebuilt coarse each time the mouse pauses, then at your Smallest Detail when you drop it. A cluster keeps its wax until you drop it.
- A candle moved, turned or scaled another way (the Move tool’s gizmo, several objects at once, a typed value) lands back on its support when the move ends.
With the 3D cursor
With Stands On on Object and a Support picked, BUILD CANDLE stands the candle on the support under the 3D cursor: on the level the cursor is on (a lower shelf, a step), or on top when the cursor is not over it. Aim from above: seen from the front, Shift + right click lands on the front of the object. A cursor on a place the candle cannot stand on sends it to the nearest place it can.
How the wax behaves
- Drips run down the candle, then downhill along the support.
- Where the surface is flat, they spread into a puddle.
- Where the surface turns under (an edge, the side of a skull), they hang as drips ending in drops.
- Puddles, the melted foot and the wax balls sit on the surface, following its slope.
- On a thin support, no wax comes out under it.
The support stays an object
The candle keeps its support as an object, not as a name: renaming the support changes nothing. If the support is deleted, the status line says so and the candle keeps its wax — it never drops to the floor. Pick another support with the eyedropper, or set Stands On to Ground.
The candle does not follow its support by itself. After moving or editing the support, select the candle and press Rebuild Selected.
Scope limitation
Wax that goes inside the support stays in the candle mesh, hidden by the support. It adds triangles but is never seen. The support itself is not part of the candle and is not exported with it. Only the support counts: a candle on a skull does not see the bones around it.
Last updated: 2026-11-09