Bucket

Every setting of the bucket in Souls Prop Builder, as the panel shows it.

Tapered stave bucket: bottom, hoops, an optional bail through two ears (rod or rope, posable). Each stave breaks off on its own in SDF.

Dimensions

SettingWhat it does
Rim heightHeight of the bucket in cm, from the ground to the rim (at least 5). The two ears of the handle rise above it.
Top diameterOutside diameter of the bucket at the rim, in cm. The staves run straight from the bottom diameter to this one.
Bottom diameterOutside diameter of the bucket at the ground, in cm. Smaller than the top diameter gives the usual flared bucket.

Staves

SettingWhat it does
StavesHow many staves go around (6 to 48). More staves give a rounder wall and narrower boards.
ThicknessThickness of each stave in cm, measured inward from the outside. It never goes past 45% of the end radius (bottom radius on a bucket).
GapSpace between two neighbouring staves, in cm. 0 = staves tight against each other.
Width variationMakes the staves unequal in width (0 to 0.5): each one is up to this share wider or narrower than the average, set by the seed. The head boards vary the same way.
SegmentsSections along the height of each stave (2 to 24). More segments follow the bulge more smoothly but add triangles; a straight bucket needs few.
Uneven topEach top corner of each stave ends up to this many cm below the rim, at random (seed driven), so the top is cut askew like an old barrel. 0 = all level.
Uneven bottomEach bottom corner of each stave starts up to this many cm above the ground, at random (seed driven). 0 = all staves stand flat on the ground.
BevelRounds every sharp edge of the bucket: staves, ears, bottom boards and iron hoops. Off: crisp edges, the lightest mesh.
Bevel sizeWidth of the rounded edges, in cm. It never eats more than 45% of the thinnest board or hoop.

Hoops

SettingWhat it does
Hoop typeMetal: a flat iron band hugging the staves, with optional nails. Rope: a twisted rope ring, set by Strands, Twist and the Rope look.
CountHow many hoops (0 to 8). Changing it puts every hoop back on the automatic layout for that count; then move each one with its own height slider.
SegmentsMetal: 0 = one flat side per stave, lying flat on it; higher = a rounder band with that many sides. Rope: at least this many sections around the ring (the twist may need more).
WidthMetal: height of the band along the barrel, in cm. Rope: diameter of the rope, in cm.
ThicknessThickness of the metal band in cm, how far it stands out from the staves.
NailsA dome nail head on every metal hoop over the middle of each stave still there at that height, the ears included. Band and nails stay one piece for SDF.
Nail headDiameter of the nail heads in cm. Never wider than 90% of the band’s width.
Reset hoop heightsPuts the hoops back on the automatic heights for their count, then rebuilds if Live update is on.
Hoop heightWhere this hoop sits, as a share of the bucket’s height: 0 = bottom, 1 = rim. The band is always kept whole on the bucket.
RopeModeled: round strands in the geometry. Game: a light tube with one crest and groove per strand; a tiling normal map made by the add-on draws the strands (written next to the FBX for Unreal).
StrandsHow many strands are twisted together in the ropes (2 to 8): rope hoops and the ropes laid over a barrel. The bucket’s rope bail has its own, under Handle.
TwistHow tightly the strands wind: turns per rope diameter of length (0 to 1). A rope ring always closes on a whole number of turns.
Strand sidesRoundness of each strand of the modeled rope (3 to 16). More sides, rounder strands, more triangles.
Low poly + high polyRope hoops and the rope bail become plain 8-sided tubes. A hidden <name>_high copy keeps them twisted; Export low + high writes both FBX to bake in Painter (By Mesh Name).

Handle

SettingWhat it does
HandleTwo opposite staves become ears above the rim, each with a real hole, and a bail runs through them. The bail is a separate child object.
BailMetal: a round iron rod. Rope: a laid rope rising between the ears, out through the holes and tied outside each ear with a stopper knot too big for the hole. The holes fit the bail.
Start loweredBuilds the bail already down. A metal bail is swung to one side, resting on the staves; a rope bail hangs outside, over the rim beside each ear and against the side of the bucket. Off: it stands up over the bucket.
Ear heightHow far the two ears rise above the rim, in cm. The holes sit a little above the middle of the ears.
Bail thicknessDiameter of the bail, rod or rope, in cm. The holes in the ears grow with it.
StrandsHow many strands are twisted together in the rope bail (2 to 8; real ropes mostly have 3). They twist like a laid rope, a full turn about every three rope diameters.
Knot sizeSize of the two stopper knots. 1: as tight as the rope can really be pulled. Smaller draws them tighter still; below 0.5 their turns show sinking into each other up close.
RopeModeled: round strands in the geometry. Game: a light tube with one crest and groove per strand; a tiling normal map made by the add-on draws the strands (written next to the FBX for Unreal).
Low poly + high polyRope hoops and the rope bail become plain 8-sided tubes. A hidden <name>_high copy keeps them twisted; Export low + high writes both FBX to bake in Painter (By Mesh Name).

Heads

SettingWhat it does
FloorThe bucket’s floor: boards laid side by side inside the staves, set the Inset above the bottom rim.
InsetHow far each head sits inside the staves, in cm from its rim (the top head below the top rim, the bottom one above the bottom rim).
ThicknessThickness of the head boards in cm.
Board widthRough width of each head board in cm, when Count is 0: the head is split into as many boards as fit, so they come close to it. They vary with the stave width variation.
GapSpace between two head boards, in cm.
CountHow many boards make each head (0 to 40). 0 = automatic, from the board width.
AngleTurns the direction of the head boards around the barrel’s axis, in degrees.

Damage

SettingWhat it does
Missing stavesHow many staves are removed, picked at random (never the bucket’s ears). Nails over a missing stave go with it.
Broken stavesHow many staves are snapped across, picked at random (never the bucket’s ears): the part kept stands on the ground or hangs from the top.
Kept lengthShare of its height a broken stave keeps (0.2 to 0.9).

Last updated: 2026-11-09

Type to search titles, sections and keywords.