Cart

Every setting of the cart in Souls Prop Builder, as the panel shows it.

Two-wheeled cart: shafts, plank bed, sides on posts, spoked wheels with iron tires. Every plank, spoke and post is its own SDF piece.

Dimensions

SettingWhat it does
Bed lengthLength of the bed, front to back, in cm. The floor planks run this way.
Bed widthWidth of the bed across, in cm. The floor planks share it.
Floor heightHeight of the top of the floor above the ground, in cm.

Damage

SettingWhat it does
Missing floor planksHow many floor planks are left out, picked at random. The seed of the damage chooses which.
Broken floor planksHow many floor planks are snapped across: only the part at the front or at the back stays on the beams.
Missing side boardsHow many side boards are left out, picked over both sides and any closed end.
Broken side boardsHow many side boards are snapped: the front or the back part stays on its posts, the broken end ragged.
Missing spokesHow many spokes are left out, counted over both wheels.
Broken spokesHow many spokes are snapped, over both wheels: the piece left on the hub or on the rim keeps a ragged end.
Kept lengthShare of its length a broken plank, board or spoke keeps (0.55 = 55%).

Bed

SettingWhat it does
Floor planksHow many planks lie lengthwise on the beams across the bed’s width. Each has its own length, so the ends never line up.
Plank thicknessThickness of the floor planks, in cm.
GapSpace between two floor planks, in cm.
Width variationHow much each floor plank’s width differs from the others, as a share (0.18 = up to 18%). 0 makes them all equal; the bed width stays the same.
Cross beamsHow many beams cross the shafts under the floor, spread along the bed. The planks lie on them.
Beam widthWidth of each cross beam along the bed, in cm.
Beam heightHeight of each cross beam, in cm; it lifts the floor above the shafts.
RoughnessHand-hewn look of every wooden piece: 0 is clean sawn boxes, 1 very rough (uneven chamfers, wandering faces, ends cut askew, chipped corners). Cut into the wood, never added.
IronworkAdds the iron details: bolt heads on the planks over the end beams, bands and nails on the side posts, bolts on the axle plates, bands on the hubs and sleeves on the shaft tips.

Sides

SettingWhat it does
SidesAdds the boards and posts along both sides of the bed.
BoardsHow many boards on edge are stacked on each side, 0 to 8.
Board heightHeight of each side board, in cm.
Board thicknessThickness of the side boards, in cm.
Gap above floorSpace between the floor’s top and the lowest side board, in cm.
Gap between boardsSpace between two stacked side boards, in cm.
PostsSquare hewn posts per side holding the boards. With as many posts as cross beams, each stands against a beam’s end.
Post sizeSide of each square post, in cm.
Post above boardsHow far the posts rise above the top side board, in cm.
Closed endsWhich ends of the bed get boards across, nailed to the corner posts: none (Open), the back, the front or both.

Wheels

SettingWhat it does
Wheel diameterOutside diameter of each wheel, tire included, in cm. The axle sits at the wheel’s centre height.
SpokesSpokes in each wheel, 4 to 32. The wooden rim is made of one segment per two spokes.
TrackDistance between the two wheels’ centres, in cm. It is kept wide enough for the wheels to clear the bed and the hubs to clear the shafts.
Hub lengthLength of each turned hub along the axle, in cm.
Hub diameterThickness of each hub, in cm.
Rim depthHow deep the wooden rim is from its outside toward the hub, in cm.
Rim widthWidth of the wooden rim across the wheel, in cm.
Iron tireAdds an iron tire around each wooden rim. The wheel keeps its diameter: the rim shrinks inside the tire.

Shafts and axle

SettingWhat it does
Shaft lengthLength of the two shafts from the back of the bed forward, in cm; never shorter than the bed. They are also the frame under it.
Shaft sizeSide of the shafts’ square section where they are full size, in cm.
Shaft spacingDistance between the two shafts’ centres, in cm.
Tip sizeSize of the shaft tips as a share of the full shaft (0.55 = 55%). The shafts taper down to it past the bed.
Axle sizeSide of the axle’s square section, in cm. It runs between the hubs and hangs from the shafts on iron plates.
Rest on shaftsTips the whole cart forward around the axle. 0 keeps it level, as when hitched; 1 lowers it until the shaft tips rest on the ground.
ChainsHangs an iron chain under each shaft, just in front of the bed.

Last updated: 2026-11-09

Type to search titles, sections and keywords.