Crate

Every setting of the crate in Souls Prop Builder, as the panel shows it.

Board crate: corner posts and rails, boards on every side, lid, floor, optional braces and metal caps. Each board and frame piece is its own SDF body.

Dimensions

SettingWhat it does
WidthOuter size of the crate from left to right, in cm, posts and boards included. The origin sits at the centre of the floor.
DepthOuter size of the crate from front to back, in cm.
HeightOuter height of the crate, in cm, from the ground to the top of the lid (lid and floor boards included).

Faces

SettingWhat it does
Board directionHorizontal: the boards on this side run left to right, stacked up the side. Vertical: they stand upright, side by side.
Board countNumber of boards on this side. 0 = automatic: as many as fit with the board width and gap set under Boards. The boards always fill the side; a fixed count makes them wider or narrower.
Diagonal braceDiagonal brace on this side, flush with the frame, its ends cut into the corners. / and \ = one brace, X = two crossed braces half-lapped so they stay flush.
LidBuilds the lid. Off: the crate is open at the top.
Lid styleFramed: the lid boards sit inside the ring of top rails, recessed like the sides. Flat: an extra layer of boards laid over the whole top of the crate.
Lid board directionWhich way the lid boards run: along the width (X) or along the depth (Y). The battens run across them.
Lid board countNumber of lid boards. 0 = automatic from the board width and gap.
BattensCross boards (0 to 4) holding the lid boards together, running across them and spread evenly.
Batten sideUnderneath: the battens are hidden under the lid. On top: they lie over the lid boards (the crate keeps its height). A framed lid always keeps them underneath.
FloorBuilds the floor. Off: the crate has no bottom.
Floor styleFramed: the floor boards sit inside the ring of bottom rails. Flat: an extra layer of boards laid under the whole crate.
Floor board directionWhich way the floor boards run: along the width (X) or along the depth (Y).
Floor board countNumber of floor boards. 0 = automatic from the board width and gap.
Frame depthHow far the boards sit back from the outer face of the posts, rails and lid or floor rings, in cm. 0 = boards flush with the frame. Used only when there are posts, rails or a framed lid or floor.

Boards

SettingWhat it does
Board thicknessThickness of every board, in cm: sides, lid, floor and battens.
Board widthTarget width of a board, in cm. It sets how many boards fit when a count is 0 (automatic); the boards then share the space exactly.
Board gapSpace left between two neighbouring boards, in cm. 0 = boards touch.
Width variationHow much the board widths differ, as a share (0 to 0.6): 0.2 lets a board be up to 20% wider or narrower. The boards still fill the face exactly.
Angle variationEach side board is turned a little in its own plane, at random up to this angle in degrees. 0 = all perfectly straight.
Length variationEach board is shortened at random by up to this share of its length (0 to 0.3), leaving uneven ends. 0 = every board full length.

Frame

SettingWhat it does
Corner postsFour square posts standing in the corners, holding the side boards. Off: the boards meet at the corners.
Post sizeSide of the square corner posts, in cm.
Top/bottom railsA ring of rails round the top and another round the bottom of the sides. A framed lid or floor always gets its ring, even when this is off.
Rail sizeSide of the square rails, in cm.
Brace widthWidth of the diagonal braces, in cm. Their ends are cut into the corners between post and rail.

Hardware

SettingWhat it does
Corner bracketsA bent metal cap on each of the 8 corners, each made as one piece of sheet folded round the corner.
Cap styleChamfered squares: three square plates with their outer corner cut. Tapered plates: a square plate on top or bottom and two plates narrowing along the vertical edge.
Fit to frameKeeps each cap no wider than the post and rails it sits on, whatever the cap size says.
Cap sizeSide of the cap plates, in cm (also capped at half the crate’s width, depth and height).
Cap cutShare of each square plate cut off at its outer corner (0 to 0.9). With tapered caps it cuts only the square top or bottom plate.
RivetsSmall dome rivets on the side plates of each cap, two per plate. They are fused to their cap so they never fly off on their own in SDF.
StrapsMetal bands (0 to 6) running round the four sides, spread evenly up the height.
Metal thicknessThickness of the corner caps and the straps, in cm.
Cap lengthLength of the tapered side plates along the vertical edge, as a multiple of the cap size (0.5 to 4).
Cap tipWidth of the tapered plates at their tip, as a share of the cap size: 1 = no taper, small = a sharp point.

Damage

SettingWhat it does
SideWhich side of the crate the counts below apply to: front, back, left, right, lid or floor. Each side keeps its own counts.
Missing boardsBoards removed from this side, picked at random. The boards left keep their places.
Broken boardsBoards snapped off on this side, picked at random: each keeps the Kept length share of its length, from one end or the other.
Kept lengthShare of its length a broken board keeps (0.2 to 0.9), for the broken boards counted on this side.
Missing boardsLid boards removed, picked at random. The boards left keep their places.
Broken boardsLid boards snapped off, picked at random: each keeps the Kept length share of its length, from one end or the other.
Kept lengthShare of its length a broken lid board keeps (0.2 to 0.9).
Missing boardsFloor boards removed, picked at random. The boards left keep their places.
Broken boardsFloor boards snapped off, picked at random: each keeps the Kept length share of its length, from one end or the other.
Kept lengthShare of its length a broken floor board keeps (0.2 to 0.9).

Last updated: 2026-11-09

Type to search titles, sections and keywords.